1021 - Design Suggestions For Ballast Water And Sediment Management Options In New Ships

 

Ref. T5/1.01                                                                                                               MEPC/Circ.389ef: Ref.T3/1.02                                                                                                                MSC/Circ.1021

21 March 2002

 

 

 

 

1          Ballastwatercarriedinshipstomaintainsafetyandstabilityhasbeenrecognizedasoneof themajorpathwaysforthetransferofharmfulaquaticorganismsandpathogensaroundtheworld. ThisthreattotheaquaticenvironmenthasbeenacknowledgedbytheConventiononBiological Diversity,1992,inArticle196oftheUnitedNationsConventionontheLawoftheSea,1982,and by other relevant international agreements.

 

2          Adraftinternationalconventionforthecontrolandmanagementofship'sballastwaterand sediments  as  well  as  associated  guidelines  for  its  implementation  is    being  developed  for consideration  and  adoption  by  a  diplomatic  conference  in  2003.   This  is  based  on  resolution A.868(20)concerningtheGuidelinesforthecontrolandmanagementofship'sballastwaterto minimize the transfer of harmful aquatic organisms and pathogens.

 

3          Theparamountimportanceofthesafetyofashipisacknowledgedwhendevelopingballast water  management  measures  to  prevent,  reduce  and  eliminate  the  transfer  of  harmful  aquatic organisms and pathogens.

 

4          Itwasagreedthatitisessentialtocontinuethedevelopmentofsaferandmoreeffective BallastWaterManagementoptionsthatwillresultincontinuedreductionandeventualelimination of the transfer of harmful aquatic organisms and pathogens.

 

5          TheMaritimeSafetyCommitteeatitsseventy-fourthsession(May2001)andtheMarine EnvironmentProtectionCommitteeatitsforty-seventhsession(March2002)emphasizedtheneed forballastwaterandsedimentmanagementoptionstobetakenintoaccountwhendesigningand buildingnewships,whilenotingthatthefutureconventionmightrequirethedevelopmentofballast watermanagementplansbothfornewandexistingshipsandapprovedtheGuidanceonìDesign SuggestionsforBallastWaterandSedimentManagementOptionsinNewShipsî,assetoutinthe annex hereto.

 

6          MemberGovernmentsareinvitedtoapplytheannexedGuidanceuntiltheInternational ConventionfortheControlandManagementofShips.BallastWaterandSedimentsisadoptedand entersinto force,tobringtheGuidancetotheattentionofship-builders,ship-owners,shipmasters andotherpartiesconcerned.  MemberGovernmentsarealsoinvitedtoinformtheOrganizationon any experience gained in the implementation of this Guidance.

 

***

 

Annex

DESIGN SUGGESTIONS FOR BALLAST WATER AND SEDIMENT MANAGEMENT OPTIONS IN NEW SHIPS

 

1          Introduction

 

1.1       Ballastwatercarriedinshipstomaintainsafetyandstabilityatseahasbeenrecognizedas oneofthemajorpathwaysforthetransferofharmfulaquaticorganismsandpathogensaroundthe world.  Althoughballastwaterhasbeencarriedaroundtheworldformanyyears,interestinballast waterasaglobalenvironmentalproblemhasonlyattractedsignificantinterestinrecentyearswith thedocumentedestablishmentofanumberofaquaticpestspecies.  Thesignificanceoftheproblem hasbeeninfluencedgreatlybytheexpansioninworldwideshippingandreducedvoyagetimeswith some12billiontonnesofballastwaternowcarriedaroundtheworldannually.  Scientificresearch indicates that several thousand species are transported in the ballast water of ships each day.

 

1.2       Therefore,theneedisemphasizedforballastwaterandsedimentmanagementoptionstobe takenintoaccountwhendesigningandbuildingnewshipsand,inthisregardtheshippingindustry shouldbecontactedfordesignconsiderations.  Arangeofsuggesteddesignconsiderationsfornew ships are given in the guidance.

 

2          Considerations at the design phase of newships

 

Ballast water management equipment

 

2.1       Ballastwatermanagementandtheprocesseschosentoachieveitshouldbeconsideredasa basic component of the ship's design.

 

2.2       Designandinstallationoftheballastwaterpumpingandpipingsystemshouldensurethatthe ease of operation and maintenance is maximized.

 

2.3       Ballast tank design should facilitate all aspects of ballast water management.

 

2.4       Installationofrecordingequipmentshouldbeconsideredforallballastwateroperationsand treatmentactions.   Itshouldbepossiblefortheserecordstobereadilyavailabletoappropriate authorities that may request copies.

 

2.5       Remote data management should be considered.

 

2.6       Mechanisms  should  be  designed  into  the  equipment  for  ready  analysis  of  system performance.

 

2.7       ABallastWaterManagementPlanshouldbecreatedfortheshipasthemethodsusedare established;inparticularitshouldgiveguidanceonsafeandeffectiveoperationofthevarious ballast water management and treatment options that are considered appropriate for the ship.

2.8       TheBallastWaterManagementPlanshouldaddresstrainingofthecrewintheballastwater management processes described therein.

 

 

 

Sampling

 

2.9       Ballast watersystemdesigns should take special account oftheincreasedneedforcontent sampling,withanaimtoenhancethequalityandeaseofsamplingofballastwaterandsediments, withouttheneedtoenterpotentiallydangerousspacesortopartiallyfillballasttanks.  Examplesof procedures and equipment are as follows:

 

.1         fittingoftankerhatches,whereverpossible,asanalternativetomanholestoallow more ready access to tanks;

 

.2         ensuringtheareaimmediatelybelowanytankopeningiskeptfree(totheextent possible) of obstructions that may impede the lowering of sampling equipment;

 

.3         installationofsamplingpipeswithinair/breatherpipesasanalternativetoaccessing tanksbymanholesortankerhatches.   Samplingpipesshouldbeterminatedata convenientlocationonthetoporsideoftheairpipe,sothatasamplingpumpmaybe easily fitted to the outlet;

 

.4         installationofstandalonesamplingpipesthatdirectlypenetrateintotheballasttanks withtheendsofsamplingpipeslocatedwithintankstoensurerepresentativeballast water samples are taken;

 

.5         fittingofaquickreleasecouplingonsamplingpipestopermittheextractionof samples without removing the manhole cover or opening the tanker hatch;

 

.6         providing safe access to tanks (especially where access is not normally required);

 

.7         sounding pipe designs should also be enhanced to facilitate taking representative samples;

 

.8         provisionforin-linesamplingfromeithertheballastpumporsomeotherpointofthe ballast  pipework,  to  permit  sampling  either  during  ballasting  or  deballasting operations; and

 

.9         giventhepotentialforvariabilityofflowwithintheballastwaterpipeworkattention shouldbegiventoensuringuniformsampling,e.g.,throughuseofastaticmixer directly ahead of the sampling pipe.

 

Ballast water exchange at sea

 

2.10     WhereBallastWaterExchangeatseaisthechosenmethod,theoveralldesignstrengthand stabilityoftheshipshouldbesufficienttopermititsexecutiononallballastvoyagesandinall exceptsevereweatherconditions.  Fortheguidanceofthemaster,themaximumseastateandswell conditionsidentifiedbythebuilder,ifany,inwhichballastwaterexchangecansafelybecarriedout should be recorded in the Ballast Water Management Plan.

 

 

 

 

2.11     Thedesignoftheshipshouldmakeiteasytoachieveexchangeatsea,byreducingthe demands upon other crew resources.  In particular it should endeavour to minimize:

 

.1         the number of operational steps;

 

.2         the time taken, and

 

.3         thenumberofpartiallyloadedtanksandthedurationoftheirpartialloading,needed

to complete a ballast water exchange sequence.

 

2.12     Thedesignoftheshipshouldincludeconsiderationoftheconsequencesofballastwater exchangeatseaincluding:stability,hullgirderstrength,shearforces,resonance,sloshing,stemming, propellerimmersion,limitationsbroughtaboutbyinsufficientstrengthinvariouspartsoftheship whenthetanksaresequentiallyemptiedandappropriatestrengtheningincorporatedtoallowthis operation to be conducted safely.

 

2.13     Wherethesequentialmethodofexchangeistobeused,particularattentionshouldbegiven to  the  ballast  tank  layout,  total  ballast  capacity,  individual  tank  configuration  and  hull  girder strength.  IfthePlanrequiressimultaneouslyemptyingandrefillingcloselymatcheddiagonaltanks thenconsequentialtorsionalstressesshouldbeconsidered.   Stillwaterbendingmoments,shear forces and stability should remain at or within safe limits.

 

2.14     Wheretheflow-throughmethodofexchangeistobeusedadequateprovisionshouldbemade toavoidtheriskofoverpressurizationofballasttanksorballastpiping.   Enhancementsinthis regardmayincludetheinstallationofadditionalairpipes,installationoftankerhatches(asan alternativetodeckmanholes),internaloverflowpipes(toavoidwaterflowingoverthedeck)and interconnecting ballast trunks between tanks where applicable and possible.

 

2.15     Wherethedilution

1 Introduction

1.1 Ballast water carried in ships to maintain safety and stability at sea has been recognized as one of the major pathways for the transfer of harmful aquatic organisms and pathogens around the world. Although ballast water has been carried around the world for many years, interest in ballast water as a global environmental problem has only attracted significant interest in recent years with the documented establishment of a number of aquatic pest species. The significance of the problem has been influenced greatly by the expansion in worldwide shipping and reduced voyage times with some 12 billion tonnes of ballast water now carried around the world annually. Scientific research indicates that several thousand species are transported in the ballast water of ships each day.

1.2 Therefore, the need is emphasized for ballast water and sediment management options to be taken into account when designing and building new ships and, in this regard the shipping industry should be contacted for design considerations. A range of suggested design considerations for new ships are given in the guidance.

2 Considerations At The Design Phase Of New Ships

Alternative Water Supplies

2.26 Where use of alternative water supplies other than seawater is considered then appropriate deck and associated pipework to permit the loading of such water to the ballast tanks should be taken into account.

Ballast Water Exchange At Sea

2.10 Where Ballast Water Exchange at sea is the chosen method, the overall design strength and stability of the ship should be sufficient to permit its execution on all ballast voyages and in all except severe weather conditions. For the guidance of the master, the maximum sea state and swell conditions identified by the builder, if any, in which ballast water exchange can safely be carried out should be recorded in the Ballast Water Management Plan.

2.11 The design of the ship should make it easy to achieve exchange at sea, by reducing the demands upon other crew resources. In particular it should endeavour to minimize:

       .1 the number of operational steps;

        .2 the time taken, and

        .3 the number of partially loaded tanks and the duration of their partial loading, needed to complete a ballast water exchange sequence.

2.12 The design of the ship should include consideration of the consequences of ballast water exchange at sea including: stability, hull girder strength, shear forces, resonance, sloshing, stemming, propeller immersion, limitations brought about by insufficient strength in various parts of the ship when the tanks are sequentially emptied and appropriate strengthening incorporated to allow this operation to be conducted safely.

2.13 Where the sequential method of exchange is to be used, particular attention should be given to the ballast tank layout, total ballast capacity, individual tank configuration and hull girder strength. If the Plan requires simultaneously emptying and refilling closely matched diagonal tanks then consequential torsional stresses should be considered. Still water bending moments, shear forces and stability should remain at or within safe limits.

2.14 Where the flow-through method of exchange is to be used adequate provision should be made to avoid the risk of over pressurization of ballast tanks or ballast piping. Enhancements in this regard may include the installation of additional air pipes, installation of tanker hatches (as an alternative to deck manholes), internal overflow pipes (to avoid water flowing over the deck) and interconnecting ballast trunks between tanks where applicable and possible.

2.15 Where the dilution method of exchange is to be used adequate provision should be made for appropriate piping arrangements to facilitate the loading of ballast water and, simultaneously, the unloading of the ballast water at the same flow rate. The hydrodynamic performance of the ballast tank is crucial to ensure full water exchange and sediment scouring.

Ballast Water Management Equipment

2.1 Ballast water management and the processes chosen to achieve it should be considered as a basic component of the ship's design.

2.2 Design and installation of the ballast water pumping and piping system should ensure that the ease of operation and maintenance is maximized.

2.3 Ballast tank design should facilitate all aspects of ballast water management.

2.4 Installation of recording equipment should be considered for all ballast water operations and treatment actions. It should be possible for these records to be readily available to appropriate authorities that may request copies.

2.5 Remote data management should be considered.

2.6 Mechanisms should be designed into the equipment for ready analysis of system performance.

2.7 A Ballast Water Management Plan should be created for the ship as the methods used are established; in particular it should give guidance on safe and effective operation of the various ballast water management and treatment options that are considered appropriate for the ship.

2.8 The Ballast Water Management Plan should address training of the crew in the ballast water management processes described therein.

Ballast Water Treatment Systems

2.16 Where a ballast water management system other than ballast water exchange is to be used, equipment chosen should provide for complete treatment of all ballast water including storm ballast water. A number of alternative treatment options are under development for managing ballast water. Due consideration should be given before selecting any system to the equipment and space requirements, effectiveness in inactivating or removing aquatic organisms and pathogens, environmental soundness, and to operational, maintenance and manpower requirements. Adequate provisions should also be made for additional power requirements.

2.17 Minimizing or removal of the risk to crewmembers whilst involving in the ballast water operation should also be considered. This should include, but not be limited to, exposure to machinery, entering enclosed spaces or working excessive hours and training.

2.18 Where a treatment method using heat is to be used, the design should analyse additional power demands and insulation requirements.

2.19 Where heat treatment of the ballast water using waste heat from the main engine is contemplated, appropriate piping and pump arrangements should be installed to facilitate the sequential flushing of the ballast water. If ballast water is intended to remain at an elevated temperature for several hours to inactivate harmful aquatic organisms and pathogens contained in sediments, attention should be given to the consequences.

2.20 Where chemical and biocide treatments are envisaged the safety and environmental aspects of stowage, storage and application of such substances should be considered, in particular:

          .1 the allocation of appropriate storage areas (either on deck or adjacent to the ballast pump-pipework area in the engine room or in a designated room), preparation spaces and appropriate pipework fittings to allow the chemical-biocide to be added by an appropriate metering and mixing system to the ballast water line; and

          .2 the Ballast Water Management Plan should contain advice to shipsí personnel on the safe handling of toxic or corrosive chemicals carried on board for the purpose of dosing or otherwise treating ballast water, taking into account any instructions issued by the treatment system manufacturer.

2.21 Where filtration systems are envisaged adequate provision should be made for their installation, maintenance and repair, including provision of adequate replacement filters. Filtration systems should be sized so that they can be operated at a reasonable capacity for ballast water use. Provision should be made for the environmentally sound disposal of filter backwash.

2.22 Where cyclone type systems are envisaged adequate provision should be made for their installation, maintenance and repair. Cyclone type systems should be sized so that they can be operated at a reasonable capacity for ballast water use. Provision should be made for disposal of cyclone concentrates as for filtration systems.

2.23 Installation of ultra-violet irradiation systems should pay due attention to the need for some form of pre-filtration of the ballast water prior to treatment.

2.24 Other potential treatment systems, e.g., ozonization, oxygen deprivation, electro-ionization, will have specific installation, operation, maintenance and repair parameters that will need to be addressed.

2.25 Any ballast water treatment system should incorporate adequate monitoring systems to ensure its effective operation.

Sampling

2.9 Ballast water system designs should take special account of the increased need for content sampling, with an aim to enhance the quality and ease of sampling of ballast water and sediments, without the need to enter potentially dangerous spaces or to partially fill ballast tanks. Examples of procedures and equipment are as follows:

   .1 fitting of tanker hatches, wherever possible, as an alternative to manholes to allow more ready access to tanks;

   .2 ensuring the area immediately below any tank opening is kept free (to the extent possible) of obstructions that may impede the lowering of sampling equipment;

   .3 installation of sampling pipes within air-breather pipes as an alternative to accessing tanks by manholes or tanker hatches. Sampling pipes should be terminated at a convenient location on the top or side of the air pipe, so that a sampling pump may be easily fitted to the outlet;

    .4 installation of stand alone sampling pipes that directly penetrate into the ballast tanks with the ends of sampling pipes located within tanks to ensure representative ballast water samples are taken;

   .5 fitting of a quick release coupling on sampling pipes to permit the extraction of samples without removing the manhole cover or opening the tanker hatch;

    .6 providing safe access to tanks (especially where access is not normally required);

   .7 sounding pipe designs should also be enhanced to facilitate taking representative samples;

   .8 provision for in-line sampling from either the ballast pump or some other point of the ballast pipework, to permit sampling either during ballasting or deballasting operations; and

   .9 given the potential for variability of flow within the ballast water pipework attention should be given to ensuring uniform sampling, e.g., through use of a static mixer directly ahead of the sampling pipe.

Shore Based Or Mobile Treatment Facilities

2.27 Where consideration is given to ballast water loading or discharge using shore based or mobile treatment facilities, installation of appropriate infrastructure, such as booster pumps and associated pipe work on deck should be taken into account with a view to practical and safe operations.

3 Design Considerations To Enhance Management, Control And Operational Strategies

Ballast Pumps

3.5 The design of a shipís ballast pumps should be matched not only to the primary function of the shipís ballast water system, but also to any additional requirements to accommodate treatment systems.

Ballast Tanks

3.6       Thedesignofballasttanksshouldfacilitatetheenhancedremovalofballastwaterand sediments by:

 

.1         internalgirders,longitudinals,stiffeners,intercostalsandfloors,wherefittedshould incorporateextradrainholeswhichwillallowwatertoflowwithminimalrestriction during discharge and stripping operations;

 

.2         whereinner membersbuttagainstbulkheads,theirinstallationshouldbesuchasto prevent the formation of stagnant pools or sediment traps;

 

.3         whereinternallongitudinalsarefittedwithfacebarstiffeners,considerationshould

begiventofitthefacebarstiffenersbelowthehorizontalsurfacestoaiddrainoff fromthe stiffeners;

 

.4         flowcalculations(CFD)shouldbeundertakentodeterminethesizeofdrainholesto confirmthereissufficientflowofwatertothesuctionheadstomatchthecapacityof the discharge of ballast water;

 

.5         installationofsuctionwellsinballasttanksthatdonotformpartofthebottomofthe ship;

 

.6         considerationoftheinstallationoftankcleaningsystemstoassistwiththeremovalof sedimentsduringballastdischarge.  Also,consideration of the use of such systems during the loaded passage to assist in the minimization of sediment in a tank; and

 

.7         installation of ballast water stripping systems using eductors.

Ballast Water Suction Piping

3.2 The design of the shipís ballast water suction piping should allow for it to be maintained in a clean condition between ballasting operations, e.g., by water circulation from one tank or from sea without taking up or discharging water, or by hypochlorination.

Sea Chests

3.1 Taking into account the need for the design of sea chests to minimize skin friction of the shipís hull, generating laminar flow of water over the hull form and facilitating good flow of water into the shipís seawater suction pipes:

            .1 consideration should be given to the design of the sea chest grate openings as a primary filter of larger marine organisms;

           .2 securing arrangements should minimize the potential for the sea grate to fall off during service, e.g., by hinging the grate on the forward side;

            .3 installation of systems to allow for the cleaning and treatment of the sea chest following ballasting, e.g., by installing a steam and air connection or piping from Butterworth tank washing systems (used for cargo tank washing); and

           .4 shutting of isolation sea suction valves to prevent the fouling or contamination of the ballast water piping and systems.

Sea Suction Strainers

3.3 Taking into account the role of sea suction strainers as a secondary filter in the shipís ballast water pumping and piping system the design should minimize the mesh size of the strainers (without restricting the water flow to the ballast pumps). Consideration should be given to manufacture the strainers from stainless steel (preferably SUS 316L) to minimize the potential for corrosion of the strainers during service, and consequential loss of effectiveness as a secondary filter.

3.4 Systems and procedures should be developed for the cleaning of strainers prior to any ballasting operation.

• Informatietype: Internationaal
• Documentsoort: Circulaire niet in wetten.nl
• Toegangsrechten: Extern
• Identificatie: PUC_1827_14
• Versie: 1
• Datum beschikbaarheid: 07-11-2007
• Geldigheid van: 21-03-2002
• Wijzigingsdatum: 24-11-2016
• Titel: 1021 - Design Suggestions For Ballast Water And Sediment Management Options In New Ships
• Organisatie: International Maritime Organization (IMO)
• Taal: Nederlands
• Thema: 1000 until 1099