1226 Interim explanatory notes to the SOLAS Chapter II-1 subdivision

MSC.1/Circ.1226

Interim explanatory notes to the SOLAS Chapter II-1 subdivision and damage stability regulations

1. The Maritime Safety Committee, at its eightieth session (10 to 19 May 2005), adopted resolution MSC.194(80), containing, inter alia, amendments to SOLAS chapter II-1, replacing parts A (General), B (Subdivision and stability) and B-1 (Subdivision and damage stability provisions for cargo ships) with new harmonized subdivision and damage stability regulations based on a probabilistic concept. In adopting the new regulations, the Committee recognized the necessity of appropriate explanatory notes for their uniform interpretation and application.
   
   
2. To this end, the Maritime Safety Committee, at its eighty-second session (29 November to 8 December 2006), approved the Interim explanatory notes to the SOLAS chapter II-1 subdivision and damage stability regulations, set out in the annex, as prepared by the Sub-Committee on Stability and Load Lines and on Fishing Vessels Safety at its forty-ninth session.
   
   
3. The Interim explanatory notes are intended to provide Administrations and the shipping industry with specific guidance to assist in the uniform interpretation and application of the new harmonized subdivision and damage stability regulations.
   
   
4. Member Governments are invited to use the Interim explanatory notes when applying the new harmonized subdivision and damage stability regulations (SOLAS chapter II-1, parts A, B, B-1, B-2, B-3 and B-4) adopted by resolution MSC.194(80) and to bring them to the attention of all parties concerned.^*

---

^*The Maritime Safety Committee, at its eighty-second session, readopted, by resolution MSC.216(82), the amendments to SOLAS chapter II-1 annexed to resolution MSC.194(80) with the inclusion of new SOLAS regulations II-1/8-1 and II-1/22-1. Both of the aforementioned amendments are expected to enter into force on 1 January 2009.

Annex

Part A

PART A

Introduction

1. The harmonized SOLAS regulations on subdivision and damage stability, as contained in revised SOLAS chapter II-1, adopted by resolution MSC.194(80)^*, are based on a probabilistic concept which uses the probability of survival after collision as a measure of ships’ safety in a damaged condition. This probability is referred to as the “attained subdivision index A” in the regulations. This can be considered an objective measure of ship safety and, ideally, there would be no need to supplement this index by any deterministic requirements.
   
   
2. The philosophy behind the probabilistic concept is that two different ships with the same attained index are of equal safety and, therefore, there is no need for special treatment of specific parts of the ship, even if they are able to survive different damages. The only areas which are given special attention in these regulations are the forward and bottom regions which are dealt with by special subdivision rules provided for the cases of ramming and grounding.
   
   
3. Only a few deterministic elements, which were necessary to make the concept practicable, have been included. It was also necessary to include a deterministic “minor damage” on top of the probabilistic regulations for passenger ships to avoid ships being designed with what might be perceived as unacceptably vulnerable spots in some part of their length.
   
   
4. It is easily recognized that there are many factors that will affect the final consequences of hull damage to the ship. These factors are random and their influence is different for ships with different characteristics. For example, it wo uld seem obvious that in ships of similar size carrying different amounts of cargo damages of similar extents may lead to different results because of differences in the range of permeability and draught during service. The mass and velocity of the ramming ship is obviously another random variable.
   
   
5. Due to this, the effect of a three-dimensional damage to a ship with given watertight
   subdivision depends on the following circumstances:
   
   
   1. which particular space or group of adjacent spaces is flooded;
      
      
   2. the draught, trim and intact metacentric height at the time of damage ;
      
      
   3. the permeability of affected spaces at the time of damage;
      
      
   4. the sea state at the time of damage; and
      
      
   5. other factors such as possible heeling moments due to unsymmetrical weights.
      
      
6. Some of these circumstances are interdependent and the relationship between them and their effects may vary in different cases. Additionally, the effect of hull strength on penetration will obviously have some effect on the results for a given ship. Since the location and size of the damage is random, it is not possible to state which part of the ship becomes flooded. However, the probability of flooding a given space can be determined if the probability of occurrence of certain damages is known from experience, that is, damage statistics. The probability of flooding a space is then equal to the probability of occurrence of all such damages which just open the considered space to the sea.
   
   
7. For these reasons and because of mathematical complexit y as well as insufficient data, it would not be practicable to make an exact or direct assessment of their effect on the probability that a particular ship will survive a random damage if it occurs. However, accepting some approximations or qualitative judgments, a logical treatment may be achieved by using the probability approach as the basis of a comparative method for the assessment and regulation of ship safety.
   
   
8. It may be demonstrated by means of probability theory that the probability of ship
   survival should be calculated as a sum of probabilities of its survival after flooding each single compartment, each group of two, three, etc., adjacent compartments multiplied, respectively, by the probabilities of surviving such damages as lead to the flooding of the corresponding compartment or group of compartments.
   
   
9. If the probability of occurrence for each of the damage scenarios the ship could be
   subjected to is calculated and then combined with the probability of surviving each of these damages with the ship loaded in the most probable loading conditions, we can determine the attained index A as a measure for the ship’s ability to sustain a collision damage.
   
   
10. It follows that the probability that a ship will remain afloat without sinking or capsizing as a result of an arbitrary collision in a given longitudinal position can be broken down to:
    
    
    1. the probability that the longitudinal centre of damage occurs in just the region of the ship under consideration;
       
       
    2. the probability that this damage has a longitudinal extent that only includes spaces between the transverse watertight bulkheads found in this region;
       
       
    3. the probability that the damage has a vertical extent that will flood only the spaces below a given horizontal boundary, such as a watertight deck;
       
       
    4. the probability that the damage has a transverse penetration not greater than the distance to a given longitudinal boundary; and
       
       
    5. the probability that the watertight integrity and the stability throughout the
       flooding sequence is sufficient to avoid capsizing or sinking.
       
       
11. The first three of these factors are solely dependent on the watertight arrangement of the ship, while the last two depend on the ship’s shape. The last factor also depends on the actual loading condition. By grouping these probabilities, calculation of the probability of survival, or attained index A, have been formulated to include the following probabilities:
    
    
    1. the probability of flooding each single compartment and each possible group of two or more adjacent compartments; and
       
       
    2. the probability that the stability after flooding a compartment or a group of two or more adjacent compartments will be sufficient to prevent capsizing or dangerous heeling due to loss of stability or to heeling moments in intermediate or final stages of flooding.
       
       
12. This concept allows a rule requirement to be applied by requiring a minimum value of A for a particular ship. This minimum value is referred to as the “required subdivision index R” in the present regulations and can be made dependent on ship size, number of passengers or other factors legislators might consider important.
    
    
13. Evidence of compliance with the rules then simply becomes:
    
    A R
    
    As explained above, the attained subdivision index A is determined by a formula for the entire probability as the sum of the products for each compartment or group of compartments of the probability that a space is flooded, multiplied by the probability that the ship will not capsize or sink due to flooding of the considered space. In other words, the general formula for the attained index can be given in the form:
    
    

    A = pi si
    
    Subscript “i” represents the damage zone (group of compartments) under consideration within the watertight subdivision of the ship. The subdivision is viewed in the longitudinal direction, starting with the aftmost zone/compartment.
    
    The value of “p_i” represents the probability that only the zone “i” under consideration will be flooded, disregarding any horizontal subdivision, but taking transverse subdivision into account. Longitudinal subdivision within the zone will result in additional flooding scenarios, each with their own probability of occurrence.
    
    The value of “s_i” represents the probability of survival after flooding the zone “i” under consideration.
    

14. Although the ideas outlined above are very simple, their practical application in an exact manner would give rise to several difficulties if a mathematically perfect method was to be developed. As pointed out above, an extensive but still incomplete description of the damage will include its longitudinal and vertical location as well as its longitudinal, vertical and transverse extent. Apart from the difficulties in handling such a five-dimensional random variable, it is impossible to determine its probability distribution very accurately with the presently available damage statistics. Similar limitations are true for the variables and physical relationships involved in the calculation of the probability that a ship will not capsize or sink during intermediate stages or in the final stage of flooding.

15. A close approximation of the available statistics would result in extremely numerous and complicated computations. In order to make the concept practicable, extensive simplifications are necessary. Although it is not possible to calculate the exact probability of survival on such a simplified basis, it has still been possible to develop a useful comparative measure of the merits of the longitudinal, transverse and horizontal subdivision of the ship.

---

^*The Maritime Safety Committee, at its eighty-second session, readopted, by resolution MSC.216(82), the amendments to SOLAS chapter II-1 annexed to resolution MSC.194(80) with the inclusion of new SOLAS regulations II-1/8-1 and II-1/22-1. Both of the aforementioned amendments are expected to enter into force on 1 January 2009.

Part B

PART B

Guidance on individual regulations

 

Regulation 02 Definitions

Regulation 2 – Definitions

Paragraph 1

Subdivision length (L_s) – Different examples of Ls showing the buoyant hull and the reserve buoyancy are provided in the figures below. The limiting deck for the reserve buoyancy may be partially watertight.

Paragraph 6

Freeboard deck – See notes under regulation 13-1 for the treatment of a stepped freeboard deck with regard to watertightness and construction requirements.

Paragraph 11

Light service draught (d_l) – The light service draught (d_l) represents the lower draught limit of the minimum required GM curve. It corresponds, in general, to the ballast arrival condition with 10% consumables for cargo ships. For passenger ships, it corresponds, in general, to the arrival condition with 10% consumables, a full complement of passengers and crew and their effects, and ballast as necessary for stability and trim. The 10% arrival condition is not necessarily the specific condition that must be used for all ships, but represents, in general, a suitable lower limit for all loading conditions. This is understood to not include docking conditions or other non-voyage conditions.

Paragraph 19

Bulkhead deck – See notes under regulation 13 for the treatment of a stepped bulkhead deck with regard to watertightness and construction requirements.

 

Regulation 04 General

Regulation 4 – General

Paragraph 1

	For cargo ships complying with damage stability regulations in other IMO instruments
Reg.	Applies
Part B-1
5	X
5-1	X
Part B-2
9	X(1)
10	X
11	X
12	X
13-1	X
15	X
15-1	X
16	X
16-1	X
Part B-4
19	X
22	X
24	X
25	X(2)

 
⁽¹⁾ Only applies to ships other than tankers.
⁽²⁾ Only applies to single hold cargo ships other than bulk carriers.

Paragraph 4

See notes under regulation 7-2, paragraph 2, for information and guidance related to these
provisions.

Regulation 05 Intact stability information

Regulation 5 - Intact stability information

Reference is made to MSC/Circ.1158 regarding lightweight check.

Regulation 5-1 – Stability information to be supplied to the master

Paragraphs 3 and 4 (see also regulation 7, paragraph 2)

In cases where the operational trim range is intended to exceed ± 0.5% of L_s, the original GM limit line should be designed in the usual manner with the deepest subdivision draught and partial subdivision draught calculated at level trim and actual service trim used for the light service draught. Then additional sets of GM limit lines should be constructed on the basis of the full range of trims ensuring that intervals of 1% L_s are not exceeded. The sets of GM limit lines are combined to give one envelope limiting GM curve. The effective trim range of the curve should be clearly stated.

Regulation 06 Required subdivision index R

Regulation 6 – Required subdivision index R

Paragraph 1

To demonstrate compliance with these provisions, see the Guidelines for the preparation of
subdivision and damage stability calculations, set out in the appendix, regarding the presentation of damage stability calculation results.

Regulation 07 Attained subdivision index A

Regulation 7 – Attained subdivision index A

Paragraph 1

The probability of surviving after collision damage to the ship hull is expressed by the index A. Producing an index A requires calculation of various damage scenarios defined by the extent of damage and the initial loading conditions of the ship before damage. Three loading conditions should be considered and the result weighted as follows:

A = 0.4A_s + 0.4A_p + 0.2A_l

where the indices s, p and l represent the three loading conditions and the factor to be multiplied to the index indicates how the index A from each loading condition is weighted.
The method of calculating the A for a loading condition is expressed by the formula:

i=t
Ac = p_i [v_i s_i]
i=1

The index c represents one of the three loading conditions, index i represents each investigated damage or group of damages and t is the number of damages to be investigated to calculate A_c for the particular loading condition.

To obtain a maximum index A for a given subdivision, t has to be equal to T, the total number of damages. In practice, the damage combinations to be considered are limited either by significantly reduced survivability possibility (i.e., flooding of substantially larger volumes) or by exceeding the maximum possible damage length.

The index A is divided into part factors as follows:

pi	The p factor is solely dependent on the geometry of the watertight arrangement of the ship.
vi	The v factor is dependent on the geometry of the watertight arrangement (decks) of the ship and the draught of the initial loading condition. It represents the probability that the spaces above the horizontal subdivision will not be flooded.
si	The s factor is dependent on the calculated stability of the ship after damage in a specific initial condition.

Three initial loading conditions should be used for calculating the index A. The loading conditions are defined by their mean draught d, trim and GM.

The mean draught and trim are illustrated in the figure above.

The GM values for the three loading cond itions could, as a first attempt, be taken from the intact stability GM limit curve. If the required index R is not obtained, the GM values may be increased, implying that the intact loading conditions from the intact stability book must now meet the GM limit curve from the damage stability calculations derived by linear interpolation between the three GM’s.

Paragraph 2

The calculations for differing trim should be carried out with the same initial trim for the partial and deepest subdivision draughts. For the light service draught, the actual service trim should be used (refer to the notes to regulation 2, paragraph 11).

Each combination of the index within the formula given in regulation 7.1 should not be less than the requirement given in regulation 6.2. Each partial index A should comply with the
requirements of regulation 6.1.

Example:

Based on the GM limiting curves obtained from damage stability calculations of each
trim, an envelope curve covering all calculated trim values should be developed.

Calculations covering different trim values should be carried out in steps not exceeding 1% of Ls. The whole range including intermediate trims should be covered by the damage stability calculations. Refer to the example showing an envelope curve obtained from calculations of 0 trim and 1% of Ls.

Paragraph 5

In the forward and aft ends of the ship where the sectional breadth is less than the ship’s breadth B, transverse damage penetration can extend beyond the centreline bulkhead. This application of the transverse extent of damage is consistent with the methodology to account for the localized statistics which are normalized on the greatest moulded breadth B rather than the partial breadth.

Where corrugated bulkheads are fitted, they may be treated as ordinary stiffened bulkheads as long as the corrugation is of the same order as the stiffening structure.

Pipes and valves directly adjacent to the bulkhead can be considered to be a part of the bulkhead. The same applies for small recesses, drain wells, etc.

Regulation 7.1 Calculation of the factor pi

Regulation 7-1 – Calculation of the factor pi

General

The definitions below are intended to be used for the application of part B-1 only.

In regulation 7-1, the words “compartment” and “group of compartments” should be understood to mean “zone” and “adjacent zones”.

Zone – a longitudinal interval of the ship within the subdivision length.

Room – a part of the ship, limited by bulkheads and decks, having a specific permeability.

Space – a combination of rooms.

Compartment – an onboard space within watertight boundaries.

Damage – the three dimensional extent of the breach in the ship.

For the calculation of p, v, r and b only the damage should be considered, for the calculation of the s-value the flooded space should be considered. The figures below illustrate the difference.

Damage shown as the bold square:

Flooded space shown below:

Paragraph 1.1

The coefficients b₁₁, b₁₂, b₂₁ and b₂₂ are coefficients in the bi- linear probability density function on normalized damage length (J). The coefficient b₁₂ is dependent on whether or not L_s = L^*, the other coefficients are valid irrespective of L_s.

Longitudinal subdivision

In order to prepare for the calculation of index A, the ship’s subdivision length Ls is divided into a fixed discrete number of damage zones. These damage zones will determine the damage stability investigation in the way of specific damages to be calculated.

There are no rules for the subdividing, except that the length Ls defines the extremes for the actual hull. However, it is important to consider a strategy carefully to obtain a good result (that is a large attained index A). All zones and combination of adjacent zones may contribute to the index A.

The figure above shows different longitudinal divisions of the length L_s.

The first example is a very rough division into three zones of approximately the same size with limits where transverse subdivision is established. The probability that the ship will survive a damage in one of the three zones is expected to be low (s-factor = 0) and, therefore, the total attained index A will be lost.

In the second example the zones have been placed in accordance with the watertight arrangement, including minor subdivision (as in double bottom, etc.). The chances of getting good s- factors in this case should be good.

Where transverse corrugated bulkheads are fitted, they may be treated as equivalent plane
bulkheads, provided the corrugation is of the same order as the stiffening structure.

The triangle in the figure below illustrates the possible single and multiple zone damages in a ship with a watertight arrangement suitable for a seven-zone division. The triangles at the bottom line indicate single zone damages and the parallelograms indicate adjacent zones damages.

Figure illustrates the possible single and multiple zone damages in a ship.

As an example, the triangle illustrates a damage opening the rooms in zone 2 to the sea and the parallelogram illustrates a damage where rooms in the zones 4, 5 and 6 are flooded
simultaneously.

The shaded area illustrates the effect of the maximum absolute damage length. The p-factor for a combination of three or more adjacent zones equals zero if the length of the combined adjacent damage zones minus the length of the foremost and the aft most damage zones in the combined damage zone is greater than the maximum damage length. Having this in mind when subdividing Ls could limit the number of zones defined to optimize the attained index A.

As the p- factor is related to the watertight arrangement by the longitudinal limits of damage
zones and the transverse distance from the ship side to any longitudinal barrier in the zone, the following indices are introduced:

Paragraph 1.2

Transverse subdivision in a damage zone

Damage to the hull in a specific damage zone may just penetrate the ship ’s watertight hull or penetrate further towards the centreline. To describe the probability of penetrating only a wing compartment, a probability factor r is used, based mainly on the penetration depth b. The value of r is equal to 1, if the penetration depth is B/2 where B is the maximum breadth of the ship at the deepest subdivision draught ds, and r = 0 if b = 0.

The penetration depth b is measured at level deepest subdivision draught ds as a transverse
distance from the ship side right-angled to the centreline to a longitudinal barrier.

Where the actual watertight bulkhead is not a plane parallel to the shell, b should be determined by means of an assumed line, dividing the zone to the shell in a relationship b₁/b2 with ½ = b₁/b₂ = 2.

Examples of such assumed division lines are illustrated in the figure below. Each sketch
represents a single damage zone at a water line plane level ds and the longitudinal bulkhead represents the outermost bulkhead position below d_s + 12.5 m.

In calculating r-values for a group of two or more adjacent compartments, the b-value is common for all compartments in that group, and equal to the smallest b- value in that group:

b = min {b₁, b₂, …, b_n}

where:	n =	number of wing compartments in that group;
	b1, b2, …, bn =	mean values of b for individual wing compartments contained in the group.

Accumulating p

The accumulated value of p for one zone or a group of adjacent zones is determined by:

k=K_j,_n
p_j,n = p_j,n,k
k=1

j+n-1
where K_j,n =  K_j the total number of b_k’s for the adjacent zones in question.
j

The figure above illustrates b’s for adjacent zones. The zone j has two penetration limits and one to the centre, the zone j+1 has one b and the zone j+n-1 has one value for b. The multiple zones will have (2+1+1) four values of b, and sorted in increasing order they are:

(b_j,1 ; b_j+1,1 ; b_j+n-1,1 ; b_j,2 ; b_K)

The total accumulated p

j=T
p = p_j,n
j=1

where T is the total number of damages.

Examples of multiple zones having a different b

Examples of combined damage zones and damage definitions are given in the figures below. Rooms are identified by R10, R12, etc.

Figure:

Combined damage of zones 1 + 2 + 3 includes a limited penetration to b3, taken into account generating two damages:

 

1) to b3 with R10, R20 and R31 damaged
2) to B/2 with R10, R20, R31 and R32 damaged

Figure:

Combined damage of zones 1 + 2 + 3 includes 3 different limited damage penetrations generating four damages:

1) to b3 with R11, R21 and R31 damaged
2) to b2 with R11, R21, R31 and R32 damaged
3) to b1 with R11, R21, R31, R32, and R22 damaged
4) to B/2 with R11, R21, R31, R32, R22 and R12 damaged

 

Figure:

Combined damage of zone 1 + 2 + 3 including 2 different limited damage penetrations (b1 < b2 = b3) generating three damages::

1) to b₁ with R11, R21 and R31 damaged
2) to b₂ with R11, R21, R31 and R12, damaged
3) to B/₂ with R11, R21, R31, R12, and R22, R32 damage

A damage having a horizontal extension b and a vertical extension H₂ leads to a flooding of both wing compartment and hold; for b and H₁ only the wing compartment. The figure illustrates a partial subdivision draught dp damage.

The same is valid if b- values are calculated for arrangements with sloped walls.

The same is valid if b- values are calculated for arrangements with sloped walls.

Regulation 7.2 Calculation of the factor si

Regulation 7-2 – Calculation of the factor si

General

Initial condition – an intact loading condition to be considered in the damage analysis described by the mean draught, vertical centre of gravity and the trim. Or alternative parameters from where the same may be determined (ex. displacement, GM and trim). There are three initial conditions corresponding to the three draughts d_s, d_p and d_l.

Immersion limits – immersion limits are an array of points that are not to be immersed at various stages of flooding as indicated in paragraphs 5.2 and 5.3 of the regulation.

Openings – all openings need to be defined: both weathertight and unprotected. Openings are the most critical factor to preventing an inaccurate index A. If the final waterline immerses the lower edge of any opening through which progressive flooding takes place, the factor “s” may be recalculated taking such flooding into account. However, in this case the s value should also be calculated without taking into account progressive flooding and corresponding opening. The smallest s value should be retained for the contribution to the attained index.

Paragraph 2

Intermediate stages of flooding

The case of instantaneous flooding in unrestricted spaces in way of the damage zone does not require intermediate stage flooding calculations. Where intermediate stages of flooding calculations are necessary in connection with progressive flooding, they should reflect the sequence of filling as well as filling level phases. Calculations for intermediate stages of flooding should be performed whenever equalization is not instantaneous, i.e. equalization is of a duration greater than 60 s. Such calculations consider the progress through one or more floodable (non-watertight) spaces. Bulkheads surrounding refrigerated spaces, incinerator rooms and longitudinal bulkheads fitted with non-watertight doors are typical examples of structures that may significantly slow down the equalization of main compartments.

Flooding boundaries

If a compartment contains decks, inner bulkheads, structural elements and doors of sufficient tightness and strength to seriously restrict the flow of water, for intermediate stage flooding calculation purposes it should be divided into corresponding non-watertight spaces. It is assumed that the non-watertight divisions considered in the calculations are limited to “A” class fire-rated bulkheads and do not apply to “B” class fire-rated bulkheads normally used in accommodation areas (e.g. cabins and corridors). This guidance also relates to regulation 4, paragraph 4.

Sequential flooding computation

For each damage scenario, the damage extent and location determine the initial stage of flooding. Calculations should be performed in stages, each stage comprising of at least two intermediate filling phases in addition to the full phase per flooded space. Unrestricted spaces in way of damage should be considered as flooded immediately. Every subsequent stage involves all connected spaces being flooded simultaneously until an impermeable boundary or final equilibrium is reached. If due to the configuration of the subdivision in the ship it is exp ected that other intermediate stages of flooding are more onerous, then those should be investigated.

Cross flooding/equalization

In general, cross flooding is meant as a flooding of an undamaged space on the other side of the ship to reduce the heel in the final equilibrium condition.

The cross-flooding time should be calculated in accordance with resolution A.266(VIII). If complete fluid equalization occurs in 60 s or less, it should be treated as instantaneous and no further calculations need to be carried out. Only passive open cross-flooding arrangements without valves should be considered effective for instantaneous flooding cases.

If complete fluid equalization can be finalized in 10 min or less, the assessment of survivability can be carried out for passenger ships as the smallest values of s_intermediate,i or s_final.

In case the equalization time is longer than 10 min, s_final is calculated for the floating position achieved after 10 min of equalization. This floating position is computed by calculating the amount of flood water according to resolution A.266(VIII) using interpolation, where the equalization time is set to 10 min, i.e. the interpolation of the flood water volume is made between the case before equalization (T = 0) and the total calculated equalization time.

In any cases where complete fluid equalization exceeds 10 min, the value of sfinal used in the formula in paragraph 1.1 should be the minimum of sfinal, i at 10 min or at final equalization.

Paragraph 4

The displacement is the intact displacement at the subdivision draught in question (ds, dp and dl).

Paragraph 4.1.1

The beam B used in this paragraph means breadth as defined in regulation 2.8.

Paragraph 4.1.2

The parameter A (projected lateral area) used in this paragraph does not refer to the attained subdivision index.

Paragraph 5

In cargo ships where cross flooding devices are fitted, the safety of the ship should be maintained in all stages of flooding. The Administration may request for this to be demonstrated. Cross-flooding equipment, if installed, should have the capacity to ensure that the equalization takes place within 10 min.

Paragraph 5.2.1

Unprotected openings

The flooding angle will be limited by immersion of such an opening. It is not necessary to define a criterion for non- immersion of unprotected openings at equilibrium, because if it is immersed, the range of positive GZ limited to flooding angle will be zero so “s” will be equal to zero. An unprotected opening connects two rooms or one room and the outside.

An unprotected opening will not be taken into account if the two connected rooms are flooded or none of these rooms are flooded. If the opening is connected to the outside, it will not be taken into account if the connected compartment is flooded. An unprotected opening does not need to be taken into account if it connects a flooded room or the outside to an undamaged room, if this room will be considered as flooded in a subsequent stage.

Openings fitted with a weathertight mean of closing (“weathertight openings”)

The survival “s” factor will be “0” if any such point is submerged at a stage which is considered as “final”. Such points may be submerged during a stage or phase which is considered as “intermediate”, or within the range beyond equilibrium.

If an opening fitted with a weathertight means of closure is submerged at equilibrium during a stage considered as intermediate, it should be demonstrated that this weathertight means of closure can sustain the corresponding head of water and that the leakage rate is negligible.

These points are also defined as connecting two rooms or one room and the outside, and the same principle as for unprotected openings is applied to take them into account or not. If several stages have to be considered as “final”, a “weathertight opening” does not need to be taken into account if it connects a flooded room or the outside to an undamaged room if this room will be considered as flooded in a successive “final” stage.

Paragraph 5.2.2

Horizontal evacuation routes on the bulkhead deck include only escape routes (designated as category 2 stairway spaces according to SOLAS regulation II-2/9.2.2.3 or as category 4 stairway spaces according to SOLAS regulation II-2/9.2.2.4 for passenger ships carrying not more than 36 passengers) used for the evacuation of undamaged spaces. orizontal evacuation routes do not include corridors within the damaged space. No part of a horizontal evacuation route should be immersed.

The provisions for escape in SOLAS chapter II-2 may allow more than one watertight compartment below the bulkhead deck to be served by a common stairway within the same main vertical zone (MVZ). Partial immersion of the bulkhead deck may be accepted at final equilibrium. The new provision is intended to ensure that evacuation along the bulkhead deck to the vertical escapes will not be impeded by water on that deck. A “horizontal evacuation route” in the context of this regulation means a route on the bulkhead deck connecting spaces located on and under this deck with the vertical escapes from the bulkhead deck required for compliance with SOLAS chapter II-2.

Paragraph 5.3.1

The purpose of this paragraph is to provide an incentive to ensure that evacuation through a vertical escape will not be obstructed by water from above. The paragraph is intended for smaller emergency escapes, typically hatches, where fitting of a watertight or weathertight means of closure would otherwise exclude them from being considered as flooding points.

Since the probabilistic regulations do not require that the watertight bulkheads be carried
continuously up to the bulkhead deck, care should be taken to ensure that evacuation from intact spaces through flooded spaces below the bulkhead deck will remain possible, for instance by means of a watertight trunk.

Paragraph 6

The sketches in the figure illustrate the connection between position of watertight decks in the reserve buoyancy area and the use of factor v for damages below these decks.

In this example, there are 3 horizontal subdivisions to be taken into account as the vertical extent of damage. The example shows the maximum possible vertical extent of damage d + 12.5 m is positioned between H2 and H3. H1 with factor v1, H2 with factor v2 > v1 but v2 < 1 and H3 with factor v3 = 1.   The factors v1 and v2 are the same as above. The reserve buoyancy above H3 should be taken undamaged in all damage cases. The combination of damages into the rooms R1, R2 and R3 positioned below the initial water line should be chosen so that the damage with the lowest s- factor is taken into account. That often results in the definition of alternative damages to be calculated and compared. If the deck taken as lower limit of damage is not watertight, down flooding should be considered.

 
Paragraph 6.1

The parameters x₁ and x₂ are the same as parameters x1 and x2 used in regulation 7-1.

Regulation 7.3 Permeability

Regulation 7-3 – Permeability

Paragraph 2

The following additional cargo permeabilities may be used:

Spaces	Permeability at draught ds	Permeability at draught dp	Permeability at draught dl
Timber cargo in holds	0.35	0.70	0.95
Wood chip cargo	0.60	0.70	0.95

 

Paragraph 3

Concerning the use of other figures for permeability “if substantiated by calculations”, such
permeabilities should reflect the general conditions of the ship throughout its service life rather than specific loading conditions.

This paragraph allows for the recalculation of permeabilities. This should only be considered in cases where it is evident that there is a major discrepancy between the values shown in the regulation and the real values. It is not designed for improving the attained value of a deficient ship of regular type by the modification of chosen spaces in the ship that are known to provide significantly onerous results. All proposals should be considered on a case-by-case basis by the Administration and should be justified with adequate calculations and arguments.

 

Regulation 08 Special requirements concerning passenger ship stability

Regulation 8 – Special requirements concerning passenger ship stability

Paragraphs 3.2 to 3.5

The number of persons carried, which is specified in these paragraphs, equals the total number of persons on board (and not N = N1 + 2 N2 as defined in regulation 6).

Regulation 09 Double bottoms in passenger ships and cargo ships other than tankers

Regulation 9 – Double bottoms in passenger ships and cargo ships other than tankers

Paragraph 2

If an inner bottom is located higher than the partial subdivision draught dp, this should be
considered an unusual arrangement in accordance with paragraph 7.

Paragraph 9

For the purpose of identifying “large lower holds”, horizontal surfaces ha ving a continuous deck area greater than approximately 30% in comparison with the waterplane area at subdivision draught should be taken located anywhere in the affected area of the ship. For the alternative bottom damage calculation, a vertical extent of B/10 or 3 m, whichever is less, should be assumed.

The increased minimum double bottom height of not more than B/10 or 3 m, whichever is less, for passenger ships with large lower holds, is applicable to holds in direct contact with the double bottom. Typical arrangements of ro-ro passenger ships may include a large lower hold with additional tanks between the double bottom and the lower hold, as shown in the figure below. In such cases, the vertical position of the double bottom required to be B/10 or 3 m, whichever is less, should be applied to the lower hold deck, maintaining the required double bottom height of B/20 or 2 m, whichever is less (but not less than 760 mm).

Typical arrangement of a modern ro-ro passenger ferry

Regulation 10 Construction of watertight bulkheads

Regulation 10 – Construction of watertight bulkheads

Paragraph 1

For the treatment of steps in the bulkhead deck of passenger ships see notes under regulation 13. For the treatment of steps in the freeboard deck of cargo ships see notes under regulation 13-1.

Regulation 12 Peak and machinery space bulkheads, shaft tunnels, etc.

Regulation 12 –Peak and machinery space bulkheads, shaft tunnels, etc.

Reference is made to MSC.1/Circ.1211 concerning interpretations regarding bow doors and the extension of the collision bulkhead.

Regulation 13 Openings in watertight bulkheads below the bulkhead deck in passenger

Regulation 13 – Openings in watertight bulkheads below the bulkhead deck in passenger ships

General – Steps in the bulkhead deck

If the transverse watertight bulkheads in a region of the ship are carried to a higher deck which forms a vertical step in the bulkhead deck, openings located in the bulkhead at the step may be considered as being located above the bulkhead deck. Such openings should then comply with regulation 17 and should be taken into account when applying regulation 7-2.

All openings in the shell plating below the upper deck throughout that region of the ship should be treated as being below the bulkhead deck and the provisions of regulation 15 should be applied. See figure below.

1 Bulkhead deck 3 Ship’s side

2 Considered as located above the bulkhead deck 3 Ship’s side 4 Considered as located below the bulkhead deck

 

Paragraph 7.6

The IEC standard referenced in the footnote (IEC publication 529, 1976) has been replaced by the newer standard IEC 60529:2003.

 

Regulation 13-1 Openings in watertight bulkheads and internal decks in cargo ships

Regulation 13-1 – Openings in watertight bulkheads and internal decks in cargo ships

Paragraph 1

If the transverse watertight bulkheads in a region of the ship are carried to a higher deck than in the remainder of the ship, openings located in the bulkhead at the step may be considered as being located above the freeboard deck.

All openings in the shell plating below the upper deck throughout that region of the ship should be treated as being below the freeboard deck, similar to the bulkhead deck for passenger ships (see figure above), and the provis ions of regulation 15 should be applied.

 

Regulation 15 Openings in the shell plating below the bulkhead deck of passenger ships and the freeboard deck of cargo ships

Regulation 15 – Openings in the shell plating below the bulkhead deck of passenger ships and the freeboard deck of cargo ships

General – Steps in the bulkhead deck and freeboard deck

For the treatment of steps in the bulkhead deck of passenger ships see notes under regulation 13.
For the treatment of steps in the freeboard deck of cargo ships see notes under regulation 13-1.

Regulation 15-1 External openings in cargo ships

Regulation 15-1 – External openings in cargo ships

Paragraph 1

With regard to air-pipe closing devices, they should be considered weathertight closing devices (not watertight). This is consistent with their treatment in regulation 7-2.5.2.1. However, in the context of regulation 15-1, “external openings” are not intended to include air-pipe openings.

Regulation 16 Construction and initial tests of watertight doors, sidescuttles, etc.

Regulation 16 – Construction and initial tests of watertight doors, sidescuttles, etc.

Paragraph 2

Watertight doors should be tested by water pressure to a head of water measured from the lower edge of the door opening to the bulkhead deck or the freeboard deck, or to the most unfavourable final or intermediate waterplane during flooding, whichever is greater.

Large doors, hatches or ramps on passenger and cargo ships, of a design and size that would make pressure testing impracticable, may be exempted from regulation 16.2, provided it is demonstrated by calculations that the doors, hatches or ramps maintain watertightness at design pressure with a proper margin of resistance. Where such doors utilize gasket seals, a prototype pressure test to confirm that the compression of the gasket material is capable of accommodating any deflection, revealed by the structural analysis, should be carried out. After installation every such door, hatch or ramp should be tested by means of a hose test or equivalent.

Note: See notes under regulation 13 for additional information regarding the treatment of steps in the bulkhead deck of passenger ships. See notes under regulation 13-1 for additional information regarding the treatment of steps in the freeboard deck of cargo ships.

Regulation 17 Internal watertight integrity of passenger ships above the bulkhead deck

Regulation 17 – Internal watertight integrity of passenger ships above the bulkhead deck

General – Steps in the bulkhead deck

For the treatment of steps in the bulkhead deck of passenger ships see notes under regulation 13.

Paragraph 1

Watertight sliding doors with reduced pressure head complying with the requirements of MSC/Circ.541, as may be amended, should be in line with regulation 7-2.5.2.1. These types of tested watertight sliding doors with reduced pressure head could be immersed during intermediate stages of flooding.

Paragraph 3

These provisions are generally already accounted for in an alternative probabilistic manner by paragraphs 5.2.1 and 5.3.3 of regulation 7-2. Therefore, instead of the specified waterline, the waterline from conditions where s = 1 can be used. The open end of air pipes means pipes without any weathertight valve.

Regulation 35

Regulation 35-1 Bilge pumping arrangements

Regulation 35-1 – Bilge pumping arrangements

Paragraph 2.6

The drainage from enclosed ro-ro spaces or special category spaces should be of such capacity that two-thirds of the scuppers, freeing ports etc. on the starboard or port side are capable of draining off a quantity of water originating from both sprinkler pumps and fire pumps, taking into account a list of 1° for ships with a breadth of 20 m or more and 2° for ships with a breadth below 20 m and a trim forward or aft of 0.5°.

Scuppers on ro-ro decks should be provided, over the outlet grate, with a removable grill with vertical bars, to prevent large obstacles from blocking the drain. The grill may be placed obliquely against the side of the ship. The grill should have a height of at least 1 m above the deck and should have a free flow area of at least 0.4 m², while the distance between the individual bars should be not more than 25 mm.

 

Appendix

Guidelines for the preparation of subdivision and damage stability calculations

 

1 General

1 General

1.1 Purpose of the Guidelines

1.1.1 These Guidelines serve the purpose of simplifying the process of the damage stability
analysis, as experience has shown that a systematic and complete presentation of the particulars results in considerable saving of time during the approval process.

1.1.2 A damage stability analysis serves the purpose to provide proof of the damage stability standard required for the respective ship type. At present, two different calculation methods, the deterministic concept and the probabilistic concept are applied.

1.2 Scope of analysis and documentation on board

1.2.1 The scope of subdivision and damage stability analysis is determined by the required
damage stability standard and aims at providing the ship ’s master with clear intact stability
requirements. In general, this is achieved by determining KG-respective GM-limit curves,
containing the admissible stability values for the draught range to be covered.

1.2.2 Within the scope of the analysis thus defined, all potential or necessary damage conditions will be determined, taking into account the damage stability crit eria, in order to obtain the required damage stability standard. Depending on the type and size of ship, this may involve a considerable amount of analyses.

1.2.3 Referring to SOLAS chapter II-1, part B-4, regulation 19, the necessity to provide the crew with the relevant information regarding the subdivision of the ship is expressed, therefore plans should be provided and permanently exhibited for the guidance of the officer in charge. These plans should clearly show for each deck and hold the boundaries of the watertight compartments, the openings therein with means of closure and position of any controls thereof, and the arrangements for the correction of any list due to flooding. In addition, Damage Control Booklets containing the aforementioned informa tion should be available.

 

2 Documents for submission

2 Documents for submission

2.1 Presentation of documents

The documentation should begin with the following details: principal dimensions, ship type,
designation of intact conditions, designation of damage conditions and pertinent damaged
compartments, KG-respective GM- limit curve.

2.2 General documents
For checking of the input data, the following should be submitted:

1. main dimensions;
   
   
2. lines plan, plotted or numerically;
   
   
3. hydrostatic data and cross curves of stability (including drawing of the buoyant
   hull);
   
   
4. definition of sub-compartments with moulded volumes, centres of gravity and permeability;
   
   
5. layout plan (watertight integrity plan) for the sub-compartments with all internal and external opening points including their connected sub-compartments, and particulars used in measuring the spaces, such as general arrangement plan and tank plan. The subdivision limits, longitudinal, transverse and vertical, should be included;
   
   
6. light service condition;
   
   
7. load line draught;
   
   
8. co-ordinates of opening points with their level of tightness (e.g. weathertight, unprotected);
   
   
9. watertight door location with pressure calculation;
   
   
10. side contour and wind profile;
    
    
11. cross and down flooding devices and the calculations thereof according to resolution A.266(VIII) with information about diameter, valves, pipes length and co-ordinates of inlet/outlet;
    
    
12. pipes in damaged area when the destruction of these pipes results in progressive
    flooding; and
    
    
13. damage extensions and definition of damage cases.
    
    

2.3 Special documents

The following documentation of results should be submitted.

2.3.1 Documentation

2.3.1.1 Initial data:

1. subdivision length L_s
   
   
2. initial draughts and the corresponding GM-values;
   
   
3. required subdivision index R; and
   
   
4. attained subdivision index A with a summary table for all contributions for all damaged zones.
   

2.3.1.2 Results for each damage case which contributes to the index A:

1. draught, trim, heel, GM in damaged condition;
   
   
2. dimension of the damage with probabilistic va lues p, v and b;
   
   
3. righting lever curve (including GZ_max and range) with factor of survivability s;
   
   
4. critical weathertight and unprotected openings with their angle of immersion; and
   
   
5. details of sub-compartments with amount of in-flooded water/lost buoyancy with their centres of gravity.
   
   

2.3.2 Special consideration

For intermediate conditions as stages before cross- flooding or before progressive flooding, an appropriate scope of the documentation covering the aforementioned items is needed in addition.

 

• Informatietype: Internationaal
• Documentsoort: Circulaire niet in wetten.nl
• Toegangsrechten: Extern
• Identificatie: PUC_1959_14
• Versie: 1
• Datum beschikbaarheid: 29-12-2009
• Geldigheid van: 15-01-2007
• Wijzigingsdatum: 24-11-2016
• Titel: 1226 Interim explanatory notes to the SOLAS Chapter II-1 subdivision
• Organisatie: International Maritime Organization (IMO)
• Taal: Nederlands
• Onderwerp: Veiligheid / Safety
• Hoofdtaak: Koopvaardij / Merchant Shipping
• Thema: Zeevaart / Seagoing ships / Information / IMO Instruments (Informative) / Circulars (Informative) / MSC Circulars (Informative) / 1200 until 1299